When it comes to drum pumps, Finish Thompson has a wide variety of pumps for any need. But one challenge is there is not a lot of mobility when it comes to drum pumps. In order to operate you will need to have an air or electricity source at your drum. Sometimes that can create headaches, having to pull air hoses or extension cords across the floor creating tripping hazards.
Well FTI has come up with a solution; a cordless 12v drum pump.
The FTI EF series drum pump has the option of a 12v motor. No longer will you have to deal with the hassle of getting hoses or cords over to your drum, now you can just grab the cordless motor, attach it to the tube and start pumping.
Once you’re done, simply place the motor back on the provided charger and it will be ready when you need it next. Gone are the days of having to figure out a way to get your product close to a power source. Now you can take the pumping source to the product.
There are some limitations to the type products that the motor can be used on. For example you cannot pump flammable liquids and it has a maximum viscosity of 100cp.
This unit has a 12-volt Li-ion battery and two speed motor 8,000/12,000 rpm. It also has an IP24 splash-proof enclosure. EF series tubes are available in either 316SS and alloy 625. Tubes are available in 16, 27, 40, & 48 inch lengths.
If you’re tired of the hassle give us a call today.
When it comes to your compressed air tools, it is important that you maintain clean and dry air in order to ensure optimum performance.
Filters, Regulators, and Lubricators (FRLs) are an easy way to help maintain your air at the point of use. There are many different combinations available for you to choose from so it will depend on the application as to what combination you will need.
Filter: Filters are used to remove solid and liquid contaminants from your air. Filters can be ordered in different styles depending on the application and the particles needing to be filtered. There are options available to remove oil aerosols and solids down to 0.3 microns.
Regulator: Regulators help provide controlled, consistent air pressure to the specified piece of equipment. Your overall plant requirements may be 125psi but certain tools or equipment may only need 65psi. With an air regulator you are able to control the pressure needed at the tool and maintain optimum performance for that piece of equipment. Standard regulators have a range of 0-140psi.
Lubricators: Lubricators are used on pneumatic applications that need just a little oil to help maintain peak performance, reduce wear, and prolong service life. They are designed to provide the correct amount of oil to air ratio for general pneumatic applications. Lubricators should be installed close to the application to ensure optimum performance.
FRL’s can be purchased as individual pieces or in combo packs depending on your application.
Give us a call at 404-363-6000 and we will be happy to recommend the correct setup for your application.
Viking Parts KitsThat is the motto of Viking. Make one repair, do it right, and get it back into production. When it comes to meeting your production quotas, there is no time for pumps going down and constantly having to make repairs. With Viking repair kits, you can have everything you need to get the pump back up and running with minimal down time and you can be assured that you have the correct parts.
With Vikings “Tag and Release” program, you can have an authorized dealer come into your plant and do an inventory of all your Viking pumps. Once completed they can then provide a tag for each pump that gives the serial number, model number, and each kit part number. This way if there is an issue with one of your Viking pumps, you have all the info needed in order to choose the correct repair kit.
Viking pumps are built to the highest standards to make rebuilding an easy and cost effective option to replacing the pump. By purchasing and rebuilding your Viking pump, you can save an average of 35% of new pump price.
Viking kits also reduce the number of SKU’s your parts room needs to keep on hand. Everything in one place right when you need it so that you can get that pump repaired and back into production with minimal down time.
Give us a call today and ask about the “Tag and Release” program.
